Verdict
All guidesResearchOpen dataMethodologyAboutContact
Head-to-head · Best Jobsite Table Saws

DeWalt DWE7491RS 10-Inch Jobsite Table Saw with Rolling Stand vs SKIL TS6307-00 15 Amp 10-Inch Jobsite Table Saw

Which is the better buy? Side-by-side on rating, price, strengths, and watch-outs — with the published ratings we averaged to get there.

Verdict is reader-supported. As an Amazon Associate we earn from qualifying purchases. Some links on this page are affiliate links — if you click through and buy, we may earn a small commission at no extra cost to you. Our ratings are sourced from independent publications, not sponsors.
The short answer

DeWalt DWE7491RS 10-Inch Jobsite Table Saw with Rolling Stand comes out ahead by a narrow margin (4.7 vs 4.5). DeWalt DWE7491RS 10-Inch Jobsite Table Saw with Rolling Stand is best for: contractors and serious DIYers who rip sheet goods on site and want an accurate fence. Read the strengths below before deciding.

DeWalt DWE7491RS 10-Inch Jobsite Table Saw with Rolling Stand
Higher ratedRanked #1 in Best Jobsite Table Saws
DeWalt DWE7491RS 10-Inch Jobsite Table Saw with Rolling Stand
2 sources$599as of Nov 1

The DeWalt DWE7491RS is a 15-amp, 10-inch jobsite table saw with a rack-and-pinion fence, a 32-1/2-inch rip capacity and a folding rolling stand. Bob Vila rated it 9.5/10 after it made smooth, square and accurate cuts right out of the box, and Tool Box Buzz gave it 5/5, praising a fence that is easy to adjust and stays parallel to the blade. The trade-offs are weight and depth: the saw weighs 90 pounds, the stand took Bob Vila about an hour to assemble, and Pro Tool Reviews notes the 3-1/8-inch cut depth at 90 degrees is just shy of ripping 4x material. It suits contractors and serious DIYers who cut sheet goods on site and want an accurate fence without a shop saw.

Strengths
  • — Cut smooth, square and accurate right out of the box in Bob Vila's testing
  • — Rack-and-pinion fence adjusts easily and stays parallel to the blade
  • — 32-1/2-inch rip capacity handles large sheet goods on the jobsite
Watch-outs
  • — Heavy at 90 pounds, and the stand takes about an hour to assemble
  • — 3-1/8-inch cut depth at 90 degrees is just shy of ripping 4x material
  • — Blade-guard dust port is awkward to use, and the stock miter gauge is basic
$599 · Check Price on AmazonFull review →
SKIL TS6307-00 15 Amp 10-Inch Jobsite Table Saw
Ranked #4 in Best Jobsite Table Saws
SKIL TS6307-00 15 Amp 10-Inch Jobsite Table Saw
1 sourceall derived$299as of Nov 1

The SKIL TS6307-00 features an integrated folding stand that allows one-person setup and transport, while its rack and pinion fence system ensures smooth adjustments. Pro Tool Reviews found the locking mechanism provides a rigid feel superior to typical DIY models, though it recorded approximately 1/32-inch of variance toward the far end of the table surface. Bestusatools notes the 15-amp motor handles dense hardwoods without bogging down, but the stock 24-tooth blade is optimized only for rough cuts and should be replaced for smoother finishes. Dado stack compatibility is limited to blades 5/8-inch or less in width, requiring users to verify insert specifications before purchasing additional equipment. This saw fits contractors who prioritize portability and speed on active jobsites but may disappoint those needing fine cabinetry precision without extensive calibration.

Strengths
  • — Integrated folding stand allows one-person setup and easy transport to jobsites
  • — Rack and pinion fence system ensures smooth, precise adjustments and keeps the fence parallel to the blade
  • — 15-amp motor provides sufficient torque to cut through dense hardwoods like oak and maple without bogging down
Watch-outs
  • — Stock 24-tooth blade is optimized only for rough cuts and should be replaced for smoother finishes
  • — Dado stack compatibility is limited to blades 5/8-inch or less in width
$299 · Check Price on AmazonFull review →

Derived means the reviewer published no score, so one was inferred from their written verdict. Everything else is a number the publisher printed. How we rank.

How they stack up

DeWalt DWE7491RS 10-Inch Jobsite Table Saw with Rolling Stand

The DeWalt DWE7491RS offers a 32-1/2-inch rip capacity on a four-leg rolling stand. Its 3-1/8-inch depth of cut at 90 degrees is shallower than the Bosch GTS15-10, which cuts through 4x lumber in one pass, so framers ripping thick stock may prefer the Bosch. It costs about twice as much as the SKIL TS6307-00 and a little less than the Bosch's listed $649. Like the Ridgid 10-Inch Pro Jobsite Table Saw with Stand, it comes on a rolling stand.

SKIL TS6307-00 15 Amp 10-Inch Jobsite Table Saw

The SKIL TS6307-00 is the lightest option at 51 lbs, significantly easier to move than the Ridgid's 98 lb unit or the Bosch GTS15-10's 91 lb frame.

Specs side-by-side

SpecDeWalt DWE7491RS 10-Inch Jobsite Table Saw with Rolling StandSKIL TS6307-00 15 Amp 10-Inch Jobsite Table Saw
Blade Size10 in.—
Motor15 amp, 4,800 RPM—
Rip Capacity32-1/2 in. right, 24 in. left25.5 inches
Depth of Cut3-1/8 in. at 90°, 2-1/4 in. at 45°—
FenceRack-and-pinion telescoping—
Dust Port2-1/2 in.—
Dado Capacity3/4 in.—
Weight90 lb51 lb
StandFolding rolling stand—
Included Blade24-tooth—
Warranty3 years—
Blade Diameter—10-inch
No Load Speed—4600 RPM
← See the full ranking of best jobsite table saws